Drilling mud Equipment

As a yougn drilling mud system manufacturer in China,GN Solids Control started exporting business from 2008,just in 3 years,GN Solids has exported drilling mud systems and equipments to over 40 countries around the world.

Countries GN mud system been exported

GN has  established  agency in over 10 countries around the world  and  exported  to more than 40 overseas countries : Australia , Brazil, Canada , India, Indonesia, Kazakhstan , Kuwait, Korea, Libya, Malaysia, Morocco,Nigeria , Poland, Russia, Singapore ,Thailand, Turkey ,UAE, Ukraine, USA etc. Many repeated mud systems customers proved our reliable service.

Why GN mud system can be exported to over 40 countries?

1)Top Quality:Standard manufacture for mud system,GN is an API & ISO certified company,assures you top quality.

2)Customized Solutions:With GN experienced engineer team, GN design and make both multi-tanks mud system and single tank smart unit  according to clients requirements . Instead of a collection of equipments from various sources, the GN drilling mud system  are field-proven solids-control components specifically designed to function as a single unit. Continue reading “Mud System to 40 countries”

There are three kinds of drilling fluid, oil based fluids (OBF’s), synthetic based fluids (SBF’s), water based fluids (WBF’s). Every coin have two sides, three ways have there own advantages and disadvantages, but for water based fluids, one important factor is: enviomental friendly, while not delivering optimal performance in more challenging drilling conditions.

Enviomental drilling fluid is water based fluid, no need any biologichal process. Just screening, hydrocycling, decanting, and so on, only mechinical separation.

Continue reading “Enviomental Drilling Fluid Management”

The NOV  Brand  Rapid Mud Tank System is a two-tank unit with a total active capacity of 620 barrels (total capacity of 800 barrels). This usually used for oilfield petroleum drilling.GN Solids Control  also design and make  such Rapid Mud Tank Unit completed with all necessary Solids Control Equipments.

General Specs for the Rapid Mud Tank System.

Equipment type：Two-tank, Rapid Mud Tank System

Total tank system volume*

620 bbl (at 12 in below mud rim)

Pill (slug) tank volume73 bbl

Maximum mud weight“18 lb/gal

Process capacity (nominal)1000 gal/min

Degasser capacity (nominal)700 gal/min

Flowline 10 in manifold with cement and active bypass

Some benifits of the Rapid mud tank system: Continue reading “GN & NOV Rapid Mud Tank System”

As one of the few API and ISO certified manufacturer,GN Solids Control design various drilling mud weighting equipment and system for Petroleum drilling,Micro-Tunneling,Horizontal direction Drilling,downhole drilling etc.

To know why people need to weight the drilling mud as operation goes,firstly,we need to know

Composition of drilling mud

Water-based drilling mud most commonly consists of bentonite clay (gel) with additives such as barium sulfate (barite), calcium

carbonate (chalk) or hematite. Various thickeners are used to influence the viscosity of the fluid, e.g. xanthan gum, guar gum, glycol, carboxymethylcellulose, polyanionic cellulose (PAC), or starch. In turn, deflocculants are used to reduce viscosity of clay-based muds; anionic polyelectrolytes (e.g. acrylates, polyphosphates, lignosulfonates (Lig) or tannic acid derivates such as Quebracho) are frequently used. Red mud was the name for a Quebracho-based mixture, named after the color of the red tannic acid salts; it was commonly used in 1940s to 1950s, then was made obsolete when lignosulfonates became available. Other components are added to provide various specific functional characteristics as listed above.

While operation goes,some material as composed of the drilling mud above may lose.To keep the balance of the drilling mud,drillers need to weight the drilling mud by adding chemicals into the mud.Usually,a complete drilling mud weighting system is consist of following equipment or accessories. Continue reading “Drilling mud weighting equipment and system”

GN Solids Control design and manufacturer drilling mud system specifically for CSG (Coal Seam Gas) Drilling Mud Cleaning System.
The CSG (Coal Seam Gas) exploration and drilling is very popular in Australia.GN Solids Control has exported mud system to Australia for CSG drilling contractors.

About CSG (Coal Seam Gas)
As an end-use product, CSG is the same as natural gas, and can be utilised in all natural gas appliances and commercial applications.The difference between CSG and other natural gas is mostly how it occurs in nature. CSG collects in the coal seam by bonding to the surface of coal particles, whereas other natural gas is stored in the pore spaces between grains of sandstone or similar rock.

Coal seams in the ground are generally filled with water, and it is the pressure of the water that keeps the gas adsorbed as a thin film on the surface of the coal. The cleats, the fracture system of coal, may be interconnected and permeable. In a high quality CSG deposit the cleats are permeable enough to allow gas and water to flow freely through them.

The level of gas produced from a coal bed is dependent on the thickness of the coal, gas content, permeability and the depth of the coal seam.The coal seams that can produce CSG economically are usually between 200m to 1,000m below the surface.

As described by GN Solids Control Clients,in CSG drilling,the drilling mud usually has much fine solids sometimes up to 80% solids.Aslo the CSG drilling is very fast. Continue reading “CSG (Coal Seam Gas) Drilling Mud System”

As the mobile fast move drilling mud cleaning system are growing rapidly in poluarity,Now GN Solids is working on design for the fast move mud systems.
Welcome to contact us for further information.

GN Solids Control has exported our mud system to over 30 countries around the world.From China to Russia,Australia,Middle East etc. Continue reading “Mobile Fast Move Drilling Mud System”

As an ISO & API Certified company specilize in mud circulation system.Following GN Solids Control introduction of mud circulation systems.
Function of Mud Circulation System
A fluid called mud circulates through the drilling bit as it cuts through rock. The fluid lubricates the bit, removes rock cuttings, stabilizes the wall around the hole, and controls the pressure in the wellbore. The mud is a suspension of chemicals and minerals, such as bentonite clay in water or sometimes oil.

Processing of Mud Circulation System
Workers blend the mixture in the mud-mixing shack. The mud pumps push the fluid up the standpipe and into the drill pipe through the kelly, or through fittings in a top drive mechanism. After passing through the drill bit, the mud and cuttings circulate back to the surface through the space outside the pipe, known as the annulus, and into the return line.

The shale shaker, a vibrating screen, then separates the cuttings from the mud. The cuttings flow into lined pits or tanks, while the drilling mud flows through the de-silter and is recirculated. More fluid is added through the mixer as the drilling progresses to greater depths. When drilling is completed, the remaining fluid is trucked away for disposal or reuse at another site.

More info. about GN mud Circulation System Continue reading “Mud Criculation system”

This post GN Solids Control will share with your our configuration of 1000 GPM to 1500GPM mud cleaning system for HDD(Horizontal Directional Drilling).

Main Benefits of the mud cleaning system:

• Cost effective method of re-cycling drilling muds.
• Reduces cost of supplying fresh mud.
• Avoids cost of disposing of liquid waste.
• Cut point of 7 micron removes particles which damage triplex pumps, whilst leaving the useful bentonite particles in suspension for re-use.
• The discharge from the cleaner is virtually dry, dramatically reducing disposal costs.

  

• Reliable and durable design, based on 20 years of field experience Engineer
• High speed continuous mixing facility incorporated.

Detailed process features:

General:

A) Cleaning Tank is divided into 3 compartment,1# Shaker compartment,2# De-sander compartment,3# De-silter compartment.

B) Mixing Tank is divided into 3 compartment,4# Intermediate compartment ,5# Centrifuge compartment,6# Mixing compartment.

1)Flexible feeding of mud from mud pit to Shale Shaker.

Two 100YZ160-38B submersible slurry pump feed slurry from mud pit to 3 each Shale Shaker at capacity of 1450GPM .Slurry pump is made from Cr26 Abrasion resistant Alloy which allow users to pump high solids content fluids. Each slurry pump connected with fluids divider of Shale shaker separately by 4 inch hoses with quick connectors. Slurry pumps are controlled separately in control panel in cleaning tank & and drillers shack. The flow capacity can be controlled by valve separately. Continue reading “GN 1000 GPM to 1500 GPM mud cleaning system”

Decanter centrifuge is one part of the solids control system, and sometimes it is used separately, for diamond drilling works, some coring works in mining industry, other drilling works with small debries.

As we know, in solids control system for oil&gas drilling, after the third phase, the desilter, debries bigger than 30 (15-47) microns are cleared out.

Once a client told us that they use mi swaco 414 with tank as a centrifuge system for their diamond drilling, we find we producing the equivalent one, LW220. So after proved with our experenced engineer, then re-researched by the cooperation universities, we manufactured our own centrifuge system for diamond drilling. LW220 with mud tank. Rugged design, compact body, efficient solution.

The differential gear type is mechanical differential, and the treating capactity is ≤ 150lpm, which means the maximun capacity is 150lpm, and you even can use this to handal the drilling mud with about 20lpm.  Other specific is as shown below:

Drum diameter: 220mm

Rotary speed:1500~4800rpm (Variable Speed)

Extruder rate L/D: 4.3

Separation factor: 2800G

Motor power(explosion proof)：main power：11kw；Assistant motor: 5.5kw

Dimension ：2020×1080×755mm

Weight ：1000kg；

Operation period：continuously 24hours

If you are interested in this centrifuge system, or centrifuge itself, contact GN Solids Control.

GN supply mud system for XJ350 Workover Drilling Rig,and also can recommend reliable China workover rig manufacturer for clients full package solution.

XJ350 Workover RigXJ350 workover rig is mainly used for shallow well workover, oil testing, fishing and pump check

operations. It is equipped with a lifting system and a rotary operating system. It can be used for workover, lateral drilling and water well drilling operation if equipped with a rotary table and relevant parts.

Features XJ350 Workover Rig

◆ 102.69 ft ( 31.3m ) double section mast, hydraulically raised and telescoped.
◆ 8×8 full drive chassis for XJ350 single-drum rig.
◆ 10×8 chassis for XJ350S double-drum rig.
◆ Simple operation platform hanged on the rear is available.
◆ A rod hanger is available Continue reading “XJ350 Workover Rig”