Jan 13

Mud system will not work if there are no mud tanks. In the mud recycling system, the tanks are used to store the drilling mud to be a base where the solids control equipment to be installed. Normally, more than one mud tanks
will be used in the oil drilling mud system. For different purpose, the design of the mud tank is different, especially the inner structure of the mud tanks.
There are mainly 3 types of mud tanks recycling tank, intermediate tank and premixing tank. Then what are the different among these 3 types of mud tank?
The recycling tank is where to install the primary shakers and degasser unit, and also the de-sanding and de-silting unit. Each of equipment needs a compartment in the mud tank. As the recycled drilling mud is treated by the solids control equipment one by one. After treatment by each of the equipment, the drilling fluids will be cleaner than before. Thus the drilling fluids cannot be mixed. The wall between two compartments always has an overflow port for balance of the drilling mud in the tank.


Mud Tank System

For the tank to install the de-sander and de-silter unit, inner structure of the mud tank would be much complex as there are pipes for centrifugal pump to such the drilling fluids from inside of the tank and transfer to the cyclone for further treatment. Operator has to know which pipe is for de-sander and which pipe is the desilter.
On the mud tanks for installing the solids control equipment on, there always have the walkways and handrails. The walkways provide enough space for the operator to walk around the equipment for operation and maintenance. Intermediate tank is a type buffering tank, part of this tank is for mud recycling, and other parts are used for mud storage. Operators can easily tell how many compartment in this tank.
The premixing tank is used to mix drilling fluids. It always is connected with the jet mixer unit. The mixing pumps suck liquid from mud tank and send liquid back again with added mud materials from the hopper. Thus the pump should be able to suck the drilling mud from anywhere in the mud tank used for mixing and storage.
Therefore, in the mixing tank, there are two groups of pipelines, one for sucking, and the other one is for sending liquid back. Mug agitators and mud guns are always installed on the mixing tank.
Though, the inner structure of the above tanks is different, the outer dimension and design are always the same for purpose of easy transportation and assembling.

written by admin \\ tags: , , , , ,

Jun 17

Mud Agitator is one of the solids control equipment that is mainly used to mix the drilling fluids in the mud tanks to keep the solids inside the drilling fluids suspending other than sedimentation down to the tank bottom.
GN’s sales team ever received many inquiries on the mud agitators; unfortunately, most of the clients have no idea on how to choose the right model for their project and even don’t know how to use the equipment properly to ensure a longer life time.


Drilling Mud Agitator

GN’s sales are good at understanding clients’ specific request by asking few simple questions. With the answer from the clients, GN always could give the best proposal for clients. Now let’s see what these questions are and what information GN need to give a proposal.
a. What is the inside dimension of the mud tank or pit. From this question, GN will know the inside length, width and depth of the mud tank, and then GN will know how long the agitator shaft should be suggested for clients and how big impeller should be used. For the deep mud tank or pit, the stabilizer will be provided to hold the agitator shaft for stable performance.
b. What is the shape of the mud tank, cylinder or rectangular? Then GN will know how to design the agitator.
c. What is the electric specification, mainly GN would like to know the jobsite electric voltage and frequency. Different countries may have different frequency, the 50 Hz motor cannot be used under 60 Hz, and safety is ever the first think we should keep in mind.
d. What is the S.G. of the liquid? For very thick liquid, GN will propose bigger horse power motor to drive the agitator.
Mud agitator is always installed in mixing tank with jet mixing unit, active mud reserve tank and trip tank. For some clients who get the mud agitators from GN and make the mud tank by themselves, GN always recommends them to make the mud tank with same dimension, thus they can get the agitator all same model, which would be much better for clients’ future maintenance. GN suggest the RPM setting of the mud agitator between 40-96, too high will disturb the solids suspending, while too low will lead to solids sedimentation.

written by admin \\ tags: , , ,

Jul 27

Lots of GN’s solids control equipment has been used in Turkey project and the feedback is good. This time, GN again got order for 2 sets solid control equipment for 1000HP rig from Turkey customer.

2014.7.26 gn shale shaker and mud cleaner to Turkey (2)

The ordered equipment in this project are 2 units GNZS594 shale shaker and 1 unit GNZJ594-2S12N mud cleaner for each rig. Total 4 units shale shaker and 2 mud cleaner. The shale shaker is designed 4 screens panel that would be interchangeable with Mongoose screen.
Worth to mention is that the customer is manufacturing the mud tank in Turkey and uses our equipment. To make sure the better matching of GN equipment and the mud tank, GN would provide the drawing and technical support to the customer. GN Solids Control will also dispatch engineer to customer site for installation instruction and training when the time of assembling the mud recycling system.

2014.7.26 gn shale shaker and mud cleaner to Turkey (1)

GN Solids Control would like very much to cooperation the customers who could fabricate the mud tank by themselves and get GN’s equipment. This cooperation method would greatly reduce the cost of delivery on large size mud tank and make sure prompt delivery of order equipments.

written by admin \\ tags: , , , ,